How to Magnetize a Screwdriver? The 4 Easiest Method 2022

Have trouble holding screws? How to Magnetize a Screwdriver? If you do, don’t worry, there are a few different ways to magnetize a screwdriver. One way is to use a hammer, magnetic bit holder, or battery. Another method involves rubbing a magnet over the screwdriver’s tip. Read on for more details. After following these steps, you should be able to keep the screwdriver magnetic forever.

How To Magnetize a Screwdriver Using a Battery?

To magnetize a screwdriver, you can use a battery. To magnetize a screwdriver, you need a battery with a terminal voltage of 6-9 volts. To magnetize a screwdriver, you must wrap a wire around the handle of the screwdriver and end it near the tip. If the screwdriver is long, you do not need to magnetize it throughout. Magnetizing it near the tip will generate a magnetic field, which will last for up to a year or two.

How to Magnetize a Screwdriver? The 4 Easiest Method 2022 How To Do?

How to Magnetize a Screwdriver

Before you begin, you need to clean the tip and shaft of the screwdriver. The tip should be dry and free of dirt. A damp rag will also work. You can place the screwdriver in a plastic bag to absorb some of the moisture. Once the screwdriver is dry, you can start magnetizing it. Once you have done this, you can place it into the battery.

Using a Hammer Magnetize a Screwdriver

Using a hammer to magnetize a screwdriver is a relatively simple method. All that is required is that you place the screwdriver on a hard surface and hit it several times with a hammer close to the tip and the shank of the screwdriver. The more hammer hits you make, the more magnetization will occur. Hammering causes the atoms inside the iron screwdriver to rearrange.

While some screwdrivers will remain magnetized even after you remove the battery, others will lose their magnetization. To avoid damaging the tip of the screwdriver, you should use an insulated wire around the screwdriver’s shaft. The larger the wire, the stronger the magnet. This trick is still used today by mechanics and is still an effective way to magnetize a screwdriver.

Klein Tools 32510 Magnetic Screwdriver * 2022 Updated

Using a magnetic bit holder

The magnetic bit holder holds a steel-alloy screwdriver. It then creates a magnetic field that pulls the screwdriver into place. After a few months, the magnetic field wears off, and you will need to re-energize the screwdriver. Once the screwdriver is magnetized, you can use it to drive screws into tight areas or over the head.

To magnetize a screwdriver, first find one strong magnet. Then wrap the wire tightly around the shaft, about ten to twenty times. Then, double back and do the same thing. Repeat the process for the other side. A screwdriver must be at least three feet long, 0.9m long, or 2.5 cm long to become magnetized. Make sure that the screwdriver is large enough to hold the magnetic bit.

Rubbing a Magnet Over The Tip Of The Screwdriver

Before attempting to use a magnetic screwdriver, you must first know how to use a magnet. You can get magnetic screwdriver bits at most hardware stores. If you are new to DIY, you should only use batteries that are nine volts or lower. This way, you can use a magnetized screwdriver without having to purchase the entire kit. Just remember to use the right type of screwdriver if you plan on using this method.


First, make sure your screwdriver is clean and that it has no ferrous material on it. If the screw is too long to fit onto the screwdriver, you can try to magnetize it by placing it halfway down the screwdriver’s blade. Make sure the magnet is dry before attempting to use it. You should be able to get a long-lasting magnet from this process. To use a magnetized screwdriver, you will need a big, strong magnet. You can find these online or in hardware stores. After you have your magnet, slide the screwdriver along the shaft until it contacts the screw.

Among these methods, which screwdriver Magnetize method will you use?

Magnetic Screwdriver Set * TOP BEST 8- Review

4.5/5 - (10 votes)

1 comment

    […] How to Magnetize a Screwdriver? The 4 Easiest Method […]